Launching
Bundle Studio
A full-window planner for a launch's buys: how much, across how many wallets, and when each one goes, with the outcome worked out as you change it.
Every draft opens in Bundle Studio. The plan is in the middle; what it adds up to is on the right. Everything saves as you go.
The top bar
- The coin
- Its picture, name, ticker and launchpad. Click it to change any of them. A red dot means something needs fixing.
- CA
- The contract address, once it's set, to copy and share before launch.
- Undo and Redo
- See Undo and redo.
- Post
- Shows once you've written a post on X, to edit it.
- Launch settings
- The dev wallet, funding, sending and the full bill. See Launch settings.
- ⋯
- Share…, Group launch…, Post on X… and Archive draft. See Launching together and Group launches.
The arrow at the end folds the bar to a slim one for more room, and this device remembers it.
Buy amount
Set the buy in one of three ways, and Coinwave works out the other two:
- Amount
- What you spend across every wallet. Max fills in the most your treasury can pay for, fees and tips included.
- % of supply
- How much of the coin you end up with.
- Opening market cap
- Where the coin opens, in USD. Type
25kfor $25,000.
The wallet count sets how many wallets buy, the dev wallet included. Under it, one line tells you the share of supply and the opening market cap.
Which wallets buy
Buy with picks where the wallets come from:
- One of your groups
- Every wallet in one of your wallet groups. Groups lead the list; an empty one can't be picked. With no groups yet, Make a wallet group takes you to the wallet manager, and the draft is saved.
- Your wallets
- Idle ones from your wallet manager: holding no coin and in no running job or launch, funded ones first. A new draft starts from these, so new wallets are only made when you ask.
- New wallets
- Made just for this launch, named after its ticker.
- Just the dev
- Only the dev buys, no bundle.
How the buy splits
- Even split
- Every wallet buys the same.
- Varied split
- Each buys a little more or less than the average. Reshuffle draws new amounts.
- Biggest first
- The first buys are the biggest.
- Biggest last
- The buys grow toward the end.
- By balance
- Wallets holding more buy more.
- What each wallet holds
- Each wallet spends its own SOL; the treasury sends nothing.
Varied, biggest first and biggest last also set how far amounts stray from the average: ±15% to ±100%, your own figure, a range between two shares of the biggest buy, or One wallet, where one wallet takes the whole buy. Bars show each wallet's amount.
With What each holds, choose how much of its own SOL each wallet spends: All of it (past its fees and what it keeps back), or A range between two percents, the same two for a fixed share. Round buys rounds each buy down to two figures, like 0.43 or 1.2, never more than the wallet holds.
Start from
| Mode | What it does |
|---|---|
| Bundle | Every buy lands in the launch block with the create, before anyone else can buy. The default. |
| Quick | The create goes alone, then every buy fires the block after, each on its own. |
| Spaced | Buys go one after another, a few seconds apart. |
| Manual | Only the dev buys at launch; the rest are funded and wait for you to send them. |
Hover a mode for what it's good for and what it costs you. A mode lays out the steps for you. Change the steps by hand and the mode reads Your steps; picking a mode again starts over from it, with an Undo. On the EVM chains only Bundle is offered, since every buy goes with the create.
Beside the modes sit the setups menu and the **Snipe watch** switch.
The release timeline
With more than one step, a timeline shows when each goes out. Drag a step along it (or use the arrow keys, with Shift for whole seconds) to retime it; steps can't pass each other. Held-back buys wait in their own lane at the end. Drop wallets on a step to move them into it.
The outcome panel
- What it costs
- What leaves your treasury: buys, fees and tips, and what wallets keep for selling, less what's already in the wallets. It offers Deposit if you're short.
- You'll hold
- Your share of the supply once every buy, held ones included, has gone out.
- Opens at
- The market cap right after the launch buys. For a coin already trading, After the buys shows it beside its cap now.
- To graduate
- How far up the bonding curve the launch takes it. Elsewhere, its Migration cap, or the pool it Opens in.
- Break-even
- The market cap where selling everything gets back what the launch cost, fees included.
- Max loss
- What you'd be down if you sold everything straight after the launch.
Under the plan, Around the launch holds Fund the wallets (As it launches or Ahead of time, see Funding) and Once it's live, whose A rule… sets up rules and Volume Bot adds a Volume Bot (up to 5 per launch). The bot's card sits at the end of the timeline: pick its wallets, what it trades and its pace, and whether it starts On its own a set time after the launch lands (30 seconds to start) or When you start it on the coin's page. The readiness checks, Coin, Buys, Settings and Funds, say why one isn't clear and take you to the fix.
Undo and redo
⌘ Z undoes, ⇧ ⌘ Z redoes, back through your last 60 changes. Inside a text field they undo your typing instead. Removing wallets or a step, switching mode over your own steps and applying a setup also offer Undo in their notice. Funding wallets ahead of time can't be undone: that money really moved. Use Pull it back instead.